![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000001-2-1024x576.jpg\")
<\/figure><\/li>![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000002-3-1024x576.jpg\")
<\/figure><\/li>![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000003-1-1024x576.jpg\")
<\/figure><\/li><\/ul><\/figure>\n\n\n\nRemove the screws to this panel as well. Once you have them removed and the panel detached, simply set it aside. Visually inspect for any damage, burn marks, or anything else that needs attention.<\/p>\n\n\n\n
Look at that lint! Actually, you may have a little to a lot depending on the frequency of using your dryer and how often you clean it out.<\/p>\n\n\n\n
![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000004-3-1024x576.jpg\")
<\/figure><\/div>\n\n\n\nLet’s vacuum this out. I use a crevasse attachment for my vacuum but if you don’t have one of these use anything you can to get in there and suck that dust and lint out. The main goal is to get the lint out so worse case use your hands to pull any loose lint out taking care not to damage any of the internal components.<\/p>\n\n\n\n
Next, we’ll need to open the door and thoroughly clean inside the door panel. This is where the lint screen is for mine and lint always gathers around and inside of the door. Try to get as much out as possible.<\/p>\n\n\n\n
![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000008-1-1024x576.jpg\")
<\/figure><\/li>![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000009-1-1024x576.jpg\")
<\/figure><\/li>![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000010-1-1024x576.jpg\")
<\/figure><\/li><\/ul><\/figure>\n\n\n\nNow, we’ll tackle a piece of plastic that almost looks like a storm great. This is on the dryer cabinet underneath where the door closes. This allows air to flow through the door lint screen, out the bottom of the door, and through this grate into where the blower is. <\/p>\n\n\n\n
Inside of the dryer drum, there are two screws holding this grate on. The technical term for my dryer part is “Laundry Center Dryer Lint Screen Cover”. Remove those screws and you’ll probably need a small screwdriver to release the clips hold it in. Be careful not to break the grate or the clips. Mine is broken on one side because of the shoe shelf that goes into the dryer that hooks on there.<\/p>\n\n\n\n
![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000001-1-1024x576.jpg\")
<\/figure><\/li>![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000002-2-1024x576.jpg\")
<\/figure><\/li>![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000005-1-1024x576.jpg\")
<\/figure><\/li><\/ul><\/figure>\n\n\n\nAfter removing this plastic grate, take a brush or crevice tool on your vacuum and clean this air passageway out. This is the last step of the line before the blower. Do the best you can because chances are something is better than what it was.<\/p>\n\n\n\n
<\/figure><\/div>\n\n\n\nNow that you have it clean, go ahead and start putting stuff together again. I put the Laundry Center Dryer Lint Screen Cover back in remembering to screw the two attachment screws.<\/p>\n\n\n\n
Next, I reattach the inner guard panel and finally the out cabinet panel.<\/p>\n\n\n\n
- <\/figure><\/li>
![\"\"](\"https:\/\/www.snaservices.com\/wp-content\/uploads\/2021\/05\/Snapshot000007-1-1024x576.jpg\")
<\/figure><\/li><\/ul><\/figure>\n\n\n\nAgain, I’m not showing the how to clean the dryer vent line.<\/p>\n\n\n\n
As always if you have any questions or comments post them below or on my YouTube <\/a>video comments section and I’ll do my best to respond.<\/p>\n\n\n\n
I\u2019ve included a few links to the equipment I used and Amazon Links<\/a> below for the equipment and materials I used. <\/p>\n\n\n\n
Equipment and Materials<\/h2>\n\n\n\n
- Stainless Steel Braided Hoses<\/a><\/li>
- Channel Lock Pliers<\/a><\/li>
- Pliers<\/a><\/li>
- Bucket<\/a><\/li>
- Tape Measure<\/a><\/li><\/ul>\n\n\n\n
I hope you find this video useful and can use some of the tips presented. Feel free to leave any comments, suggestions, or experiences you have had below.<\/p>\n\n\n\n
- Channel Lock Pliers<\/a><\/li>